UPVC Replacement Door Handles
Over time, the handles on your doors will wear out and require replacement. It is crucial to be able to match the dimensions of the old handles when replacing them.
The three measurements to check are the top screw's location, lever and key hole sizes. Check the size guide for assistance with this.
Inline Lever/Lever
A lever/lever handle is a modern door handle that is designed to fit new or replacement doors. This kind door handle is offered in a wide range of designs and finishes. A number of manufacturers offer this handle including Avocet, ERA, Fullex, Hoppe, Mila, Millenco & Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The handles of uPVC/Composite are constructed from durable materials, and are ideal for doors with multiple points that require a robust design. The handles are inline and run with the same spindle as well as screw fixings so they can be easily fitted to existing or new uPVC/Composite doors.
The handle can be positioned and angled to accommodate any user. The handle has been endurance-tested to 200,000 cycles. This ensures that the finish is of high quality and performance over time. The sprung lever can also be reduced to accommodate the widest range of locks. This is particularly beneficial in doors with smaller door frames where the cylinder is further back. A shorter lever is an ideal choice for doors where the latch can be operated by a thumb turn inside.
Lever Pad
A Lever Pad upvc door handle operates differently than lever handles found on most doors. The handle can use a single spindle (inline) or independently from each side using two inline or offset spindles (pad). They are commonly employed on UPVC doors with double glazing and come in a range of finishes and variations.
The handles are available in various finishes, including White Chrome and Gold. The finish is BS EN 1670 Grade 5 and is resistant to rust. This gives the handle an outstanding performance and durability to serve its intended use.
All of the UPVC lever pad styles for handles come with screws and a spindle which allow them to be fitted on any new or existing uPVC door. The backplate fixation centres of 211mm allow for a wider handle, which is usually an advantage when replacing an old or damaged multi-point door lock mechanism. These handle levers are also spring-loaded, which solves the issue of handles that slide from their horizontal position when they are not in use.
It is essential to match the PZ dimensions for both the multipoint lock and the uPVC doors when selecting the replacement UPVC spindle and handle. This measurement is also referred to as the 'handle centre' or 'cylinder centres' and is a critical aspect in ensuring that you have the correct handles.
After you have determined the correct size of PZ and the correct PZ size, you must make sure that the lever and push pads are shaped to match the American with Disabilities Act compliant handles that you need for your door. These are usually square or round with an internal lever and an external push pad.
Most of the UPVC lever pads we offer are sprung, which means that they return to their horizontal position when they are not in use, rather than hanging out and potentially sticking in the frame. This helps prevent the draughts and cold air from entering a property. The majority of UPVC lever pad style handles come in both left and right handed versions which allows them to be placed on either side of doors.
Euro Cylinder
Cylinder locks are found on uPVC and other kinds of doors. They operate by using a key to unlock a cylinder case which is then revealed with pins that can be aligned to those in the lock body and allow them to rotate an revolving cam, opening the door. Euro Cylinders are available with up to six pins. Doors that are internal and external require different levels of security.
Choosing the right cylinder is vitally important; this is dependent on the way your door and handle are used. For instance, doors that are external must be secured with a more secure cylinder whilst internal doors can be secured with a standard cylinder. Additionally, certain cylinders are available with extra features which can enhance security, for instance anti-drill or anti-bump features.
To ensure that the euro cylinder is the right size for your door, it must be measured correctly. upvc replacement door handles Repair My Windows And Doors should be measured from the screw hole at the center to the ends of the cylinder. This includes the thumb turn in the event that one is present. It is best to do this with the lock in place however, if this is not possible, you may remove it to measure. A cylinder that extends beyond the handle and escutcheon might be vulnerable to attacks such as snapping locks, so it is essential that it is not too long.
The design of the latest cylinders comes with anti-drilling as well as bump resistance features. These are designed to reduce the chances of an attack by forcing the cylinder to rotate in a different direction. This helps prevent attacks and protect your doors.
There are also cylinders made to resist snapping. This is a growing type of attack on cylinders, where the break line inside the lock is smashed using a special tool to snap off the front of the cylinder to allow the door to be opened. This is a faster and easier way to gain access than a multipoint locking system. It also leaves no evidence of the break-in which could delay insurance claims.
Spring Cassette
This spring cassette is located inside the base plate of the door handle. It is a spring-loaded solution to help return the multipoint lock handles to their original position after usage. These handles used to have no spring and would drop when the locking mechanism was removed. This component is the best way to address this issue. It also prevents your upvc door from becoming stuck in either the closed or open position as they aren't easy to close manually.
These spring cassettes have been specifically designed to be used with sprung multipoint locks They will not work with non-sprung multipoint handles. You will need to have a hole specifically cut in your backplate to allow these to fit (please see image for technical diagram). They are a replacement for existing damaged or missing cassettes inside the backplates of door handles of various kinds of uPVC doors. They are supplied in a single unit. They come with a square cut out that can accommodate an 8mm shaft.
These spring cassettes are a great cost-effective solution to the issue of your door handles that are sagging. They are simple to install and will increase the lifespan of your uPVC door. Please contact our team for more information about our selection of uPVC accessories and spares. We are available to help and happy to provide professional advice.